https://www.vultr.com

The Everywhere Cloud

Deploy an instance.
Accelerate your application.


Standards - Note 2

By -


The following items are examples listed in 2017 PEC Appendix D (Wiring Design Examples).

Example D1: "Single Family Dwelling Unit, up to 50 square meters Floor Area with Load not exceeding 3,680 Volt-Amperes"

Example D2: "Single Family Dwelling Unit, up to 150 square meters Floor Area (Not more than six circuits)"

Example D3: "Single Family Dwelling Unit, up to 150 square meters Floor Area (More than six circuits)"

Example D4: "Single Family Dwelling Unit, up to 150 square meters Floor Area, Optional Calculation"

Example D5: "Single Family Dwelling Unit, more than 150 square meters Floor Area, 230 Volts, Single-Phase Service"

Example D6: "Single Family Dwelling Unit, more than 150 square meters Floor Area, 400/230 Volts, Three-Phase, 4-Wire Service"

Example D7: "Multi Family Dwelling Unit, 230 Volts, Single-Phase Service"

Example D8: "Multi Family Dwelling Unit, 400/230 Volts, Three-Phase, 4-Wire Service"

Example D9: "Motors, Motor Circuits, and Controllers: Single Motor"

Example D10: "Motors, Motor Circuits, and Controllers: Multiple Motors"

Example D11: "Voltage Regulators, Single-Phase, 60 Hz, 165-280 Volts Input, 230 Volts Output VR"

Example D12: "Voltage Regulators, Three-Phase, 60 Hz, 350-530 Volts Input, 230 Volts Output VR"

Example D13: "Available Short Circuit Current"

Example D14: "Simplified Fault Current Calculation"

Example D15: "Voltage Drop Calculation"

Example D16: "Feeder Ampacity Determination for Generator Field Control"

Example D17: "Feeder Ampacity Determination for Adjustable Speed Drive Control"

Example D18: "Mobile Home, Single-Phase, 2-Wire Service"

Example D19: "Park Trailer, Single-Phase, 2-Wire"

Example D20: "Store Building"

Example D21: "Industrial Feeders in a Common Raceway"

Comments

Post a Comment

Popular posts from this blog

Standards - Note 3

By -
Image
WIRE AMPACITIES, INSULATORS, AND IMPEDANCES Below are some useful tables pertaining to ampacities, insulators, and impedances of various wires. These are derived from the 2017 Philippine Electrical Code [ or the 2017 National Electrical Code ], but are rearranged in a manner that is easier to interpret and understand. 1.) Allowable Ampacities of Insulated Conductors in Raceway. The areas, ampacities, and insulation types of the following tables are based on 2017 PEC Table 3.10.2.6(B)(16) [ or 2017 NEC Table 310.15(B)(16) ]. 1.1.) Copper Wire Ampacities --------------------------------------- |  Copper  |  Insulation Max Op. Temp | --------------------------------------- |   Area   | 60degC | 75degC | 90degC | |   mm^2   |  Amps  |  Amps  |  Amps  | --------------------------------------- |    2.0   |    15  |    20  |    25  ...
Read more

Standards - Note 4

By -
Image
RACEWAY SIZES (CONDUIT AND TUBING) 1.) Raceway Sizing There are three options for sizing raceways according to 2017 PEC Table 10.1.1.1 [ or 2017 NEC Chapter 9 Table 1 ], based on cross-sectional areas: A.) 53% raceway area for 1 conductor (a multiconductor cable is treated as a single conductor [Note 9]) B.) 31% raceway area for 2 conductors C.) 40% raceway area for over 2 conductors 1.1.) Choosing Between Alternatives For future expansion purposes, option (A) is far from practical. This may have use in very specific installations that are assumed to be not needing any expansions, but upgrades will definitely happen and option (A) will eventually become a bottleneck. Option (B) for 2 conductors having a smaller area than either option (A) for 1 conductor or option (C) for over 2 conductors may seem nonsensical, but it actually does make sense. Having 2 conductors usually means 2 live wires supplying loads that may require an equipment grounding conductor ...
Read more

Faults - Scenario 4

By -
Image
This post demonstrates how to estimate the kiloAmpere Interrupting Capacity (kAIC) rating of the first circuit breaker at the secondary side of a transformer using the Infinite Bus Method. The method assumes infinite supply from the primary side with negligible line impedances. Below is a modified version of Example D13 (Available Short Circuit Current)  in Appendix D of the 2017 Philippine Electrical Code (PEC). SITUATION Two adjacent buildings are supplied by two different distribution transformers. One transformer is single-phase rated 100kVA, 230V with 2.5% impedance. The other is three-phase rated 100kVA, 230V line-to-line and also has 2.5% impedance. What minimum kAIC ratings are needed for the first circuit breakers down the line of each transformer to safely interrupt the maximum symmetrical fault currents? ANALYSIS 1.) SINGLE-PHASE TRANSFORMER LOAD-SIDE SUB-CIRCUIT Base Power, 1ph: S,base = 100kVA Base Voltage, 1ph: V,base = 230V Impedance, ...
Read more